product datasheet strada-sq series last update 28/9/2012 ordering number description family type led color diameter height style optic material holder material fastening status C12410 C12410_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9 mm square pmma - screw, glue ready fwhm efficiency cd/lm gerber file asym degrees 93 % - available positioning: external position element / automatic assembling line. ordering number description family type led color diameter height style optic material holder material fastening status ca12411 ca12411_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9.15 mm square pmma - screw, tape ready fwhm efficiency cd/lm gerber file asym degrees 93 % 0.510 available positioning: external position element / automatic assembling line. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 general information - product series especially designed & optimized for xm-l series of leds. - special care taken to make light distribution as uniform as possible. - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 3 2 2 4 4 1 1 designed by - date - checked by vs date - drawn by as date 25.9.2012 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight 4,97 g sheet 1/1 size a4 part number rev 001 drawing title strada-sq-a-t ledil oy salorankatu 10 fin 24240 salo finland tolerances if not otherwise shown: according to din iso 2768-1 linear measures: up to 30mm class f, otherwise class m. according to din iso 2768-2 form and position: class k control for spc marked dimensions. mechanical drawing isometric view 9 front view bottom view 25 25 top view
product datasheet strada-sq series last update 28/9/2012 ordering number description family type led color diameter height style optic material holder material fastening status C12410 C12410_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9 mm square pmma - screw, glue ready fwhm efficiency cd/lm gerber file asym degrees 93 % - available positioning: external position element / automatic assembling line. ordering number description family type led color diameter height style optic material holder material fastening status ca12411 ca12411_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9.15 mm square pmma - screw, tape ready fwhm efficiency cd/lm gerber file asym degrees 93 % 0.510 available positioning: external position element / automatic assembling line. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 general information - product series especially designed & optimized for xm-l series of leds. - special care taken to make light distribution as uniform as possible. - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 3 2 2 4 4 1 1 designed by - date - checked by vs date - drawn by as date 25.9.2012 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight 4,97 g sheet 1/1 size a4 part number rev 001 drawing title strada-sq-a-t ledil oy salorankatu 10 fin 24240 salo finland tolerances if not otherwise shown: according to din iso 2768-1 linear measures: up to 30mm class f, otherwise class m. according to din iso 2768-2 form and position: class k control for spc marked dimensions. mechanical drawing isometric view 9 front view bottom view 25 25 top view
product datasheet strada-sq series last update 28/9/2012 ordering number description family type led color diameter height style optic material holder material fastening status C12410 C12410_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9 mm square pmma - screw, glue ready fwhm efficiency cd/lm gerber file asym degrees 93 % - available positioning: external position element / automatic assembling line. ordering number description family type led color diameter height style optic material holder material fastening status ca12411 ca12411_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9.15 mm square pmma - screw, tape ready fwhm efficiency cd/lm gerber file asym degrees 93 % 0.510 available positioning: external position element / automatic assembling line. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 general information - product series especially designed & optimized for xm-l series of leds. - special care taken to make light distribution as uniform as possible. - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 3 2 2 4 4 1 1 designed by - date - checked by vs date - drawn by as date 25.9.2012 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight 4,97 g sheet 1/1 size a4 part number rev 001 drawing title strada-sq-a-t ledil oy salorankatu 10 fin 24240 salo finland tolerances if not otherwise shown: according to din iso 2768-1 linear measures: up to 30mm class f, otherwise class m. according to din iso 2768-2 form and position: class k control for spc marked dimensions. mechanical drawing isometric view 9 front view bottom view 25 25 top view
product datasheet strada-sq series last update 28/9/2012 ordering number description family type led color diameter height style optic material holder material fastening status C12410 C12410_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9 mm square pmma - screw, glue ready fwhm efficiency cd/lm gerber file asym degrees 93 % - available positioning: external position element / automatic assembling line. ordering number description family type led color diameter height style optic material holder material fastening status ca12411 ca12411_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9.15 mm square pmma - screw, tape ready fwhm efficiency cd/lm gerber file asym degrees 93 % 0.510 available positioning: external position element / automatic assembling line. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 general information - product series especially designed & optimized for xm-l series of leds. - special care taken to make light distribution as uniform as possible. - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 3 2 2 4 4 1 1 designed by - date - checked by vs date - drawn by as date 25.9.2012 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight 4,97 g sheet 1/1 size a4 part number rev 001 drawing title strada-sq-a-t ledil oy salorankatu 10 fin 24240 salo finland tolerances if not otherwise shown: according to din iso 2768-1 linear measures: up to 30mm class f, otherwise class m. according to din iso 2768-2 form and position: class k control for spc marked dimensions. mechanical drawing isometric view 9 front view bottom view 25 25 top view
product datasheet strada-sq series last update 28/9/2012 ordering number description family type led color diameter height style optic material holder material fastening status C12410 C12410_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9 mm square pmma - screw, glue ready fwhm efficiency cd/lm gerber file asym degrees 93 % - available positioning: external position element / automatic assembling line. ordering number description family type led color diameter height style optic material holder material fastening status ca12411 ca12411_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9.15 mm square pmma - screw, tape ready fwhm efficiency cd/lm gerber file asym degrees 93 % 0.510 available positioning: external position element / automatic assembling line. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 general information - product series especially designed & optimized for xm-l series of leds. - special care taken to make light distribution as uniform as possible. - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 3 2 2 4 4 1 1 designed by - date - checked by vs date - drawn by as date 25.9.2012 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight 4,97 g sheet 1/1 size a4 part number rev 001 drawing title strada-sq-a-t ledil oy salorankatu 10 fin 24240 salo finland tolerances if not otherwise shown: according to din iso 2768-1 linear measures: up to 30mm class f, otherwise class m. according to din iso 2768-2 form and position: class k control for spc marked dimensions. mechanical drawing isometric view 9 front view bottom view 25 25 top view
product datasheet strada-sq series last update 28/9/2012 ordering number description family type led color diameter height style optic material holder material fastening status C12410 C12410_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9 mm square pmma - screw, glue ready fwhm efficiency cd/lm gerber file asym degrees 93 % - available positioning: external position element / automatic assembling line. ordering number description family type led color diameter height style optic material holder material fastening status ca12411 ca12411_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9.15 mm square pmma - screw, tape ready fwhm efficiency cd/lm gerber file asym degrees 93 % 0.510 available positioning: external position element / automatic assembling line. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 general information - product series especially designed & optimized for xm-l series of leds. - special care taken to make light distribution as uniform as possible. - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 3 2 2 4 4 1 1 designed by - date - checked by vs date - drawn by as date 25.9.2012 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight 4,97 g sheet 1/1 size a4 part number rev 001 drawing title strada-sq-a-t ledil oy salorankatu 10 fin 24240 salo finland tolerances if not otherwise shown: according to din iso 2768-1 linear measures: up to 30mm class f, otherwise class m. according to din iso 2768-2 form and position: class k control for spc marked dimensions. mechanical drawing isometric view 9 front view bottom view 25 25 top view
product datasheet strada-sq series last update 28/9/2012 ordering number description family type led color diameter height style optic material holder material fastening status C12410 C12410_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9 mm square pmma - screw, glue ready fwhm efficiency cd/lm gerber file asym degrees 93 % - available positioning: external position element / automatic assembling line. ordering number description family type led color diameter height style optic material holder material fastening status ca12411 ca12411_strada-sq-a-t strada-sq lens xm-l clear 25 + 25 mm 9.15 mm square pmma - screw, tape ready fwhm efficiency cd/lm gerber file asym degrees 93 % 0.510 available positioning: external position element / automatic assembling line. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 1/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 note: the typical divergence will be changed by different color, chip size and chip position tolerance. the typical total divergence is the full angle measured where the luminous intensity is half of the peak value. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 2/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 product datasheet strada-sq series last update 28/9/2012 general information - product series especially designed & optimized for xm-l series of leds. - special care taken to make light distribution as uniform as possible. - fastening to heat sink with a pu foam adhesive tape of automotive grade. please find fastening details by clicking link: http://www.ledil.com/datasheets/datasheet_tape.pdf - fastening to pcb with appropriate adhesive. by clicking link below you can find ledil recommended glue options. http://www.ledil.com/datasheets/datasheet_glues.pdf note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. note 2: assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. slanted assembly might cause unbalanced bond to the surface. all surfaces where tape is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer - this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. note 1: we advise customer to ensure the suitability and sufficiency of the bond in the end product. for example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. note 2: all surfaces where glue is applied must be clean, dry and free from grease and dirt. if cleaning of pcb surfaces is needed, please follow strictly the cleaning instructions of your led manufacturer -this is important as cleaning shall under no circumstances damage leds or other electronics components on the pcb. further note that optical components shall not be cleaned with any chemicals - only micro fiber cloth may be used to remove fingerprints or other traces from handling. october 4th 2012 0:22 copyright ledil oy - subject to change without prior notice - page 3/3 ledil oy salorankatu 10 24240 salo finland http://www.ledil.com email: ledil@ledil.com fax: +358-2-733 8001 a d b c a d 3 3 2 2 4 4 1 1 designed by - date - checked by vs date - drawn by as date 25.9.2012 this drawing is our property. it can't be reproduced or communicated without our written agreement. scale 2:1 weight 4,97 g sheet 1/1 size a4 part number rev 001 drawing title strada-sq-a-t ledil oy salorankatu 10 fin 24240 salo finland tolerances if not otherwise shown: according to din iso 2768-1 linear measures: up to 30mm class f, otherwise class m. according to din iso 2768-2 form and position: class k control for spc marked dimensions. mechanical drawing isometric view 9 front view bottom view 25 25 top view
|
